Hasegawa 1/1500 Arcadia
Finally, all works has been done! I would like to share completed work of Space Pirate Battleship Arcadia. 1st picture is all light off. Basically, I did not change anything about the shape of the ship. I modified only the scull and cross …
The last time, I thought I finished all work to do, but I cared about the flag attached on the cabin. I thought for a while then I decided I remake the flag. I was thinking and thinking, how to make a flag better, then I tried this way, Us…
The goal of this project is coming : ) Today, the Arcadia will be set to the stand. I am sure, no one remember the stand. mata1.hatenadiary.jp I tried to mount Arcadia onece, so it shoud be no problem. But since I put all LED and fibers, i…
Finally, I am starting weathering. This is the final stage of this project. But, this kit is 1/1500 of scale. If I do weathring too much, the kit looks just looking good toy. I would like to make ths ship looks like prop of some Si-fi movi…
Today, I do final assembly, and connect all electrical parts and fiber optic. Attach the bow part to the hull. I have 2 led in the bow. I pass the wiring through the hole in the hull, carefully. If I break fiber optic,,, I do not want to t…
Finally, I began painting Arcadia. I painted the deck first.Because it seemed easy for me to masking. I paint the Deck using the paint that was made by mixing Mr. Color 340( Field Green FS 34097) with black, green, red etc while watching t…
It was already long time ago, I finished base coat paint. Before I start painting, I have to finish electrical work. First, I attached the optical fiber. If I attached the fiber before I did base coat, there is some risks to break the fibe…
Following the last time, it is the base paint. On the second layer of gray, I did panel masking again. After finish masking, paint the gray of the third layer. Then, after the third layer gray is dry, peel off all of the masking. Now, pain…
Finally fabrication of Arcadia will enter the base painting. This time, I will paint several times of the layer for base using gray with different darkness. When stacking a layer, by masking as of the exterior panel every time, to represen…
I still have something to do before I start painting. Basically, I have not changed the form of the kit. But I have only one thing I would like to modify the shape. It is the skull and crossbones of the big features of the Arcadia. This is…
Finally, it will begin a base paint. But before that, eliminate the seam of the hull. Using the Tamiya putty, remove the step of the left and right , prepare the surface with sandpaper. Panel line that disappeared in the sand paper, re-car…
The work of the Arcadia has advanced only slightly. I glued the parts around the bridge. You can see optic fiber and wires from LED from the bottom. Finally it was bonded, so it is not possible to fix even if it will bebroken inside Also, …
Hello, there. I have not done up date for long time,,, So, I think that many people forgot about the brog, or what is next. I finished basic work for bridge last time, and I am going to build the base parts of the bridge. I did not change …
Today I will update after a long time. It is the assembly of the bridge, but,,, I forgot to take pictures of the middle of the process. Bridge was finished in this way. Next, I must think of the idea to deliver light to the radar on the br…
Today's topic is about the illuminations of the bridge. Below the skull mark, it is the window of the bridge. I will illumination this window. First, I will open the windows of the slit. Method is the same as the radar. On top of the main …
Today, it is the work around the bridge. Since the antenna of the kit of parts slit is closed, I was hollowed out there. In the left is a non-working state, the right is the state of being hollowed. I opened a lot of holes in the slit usin…
The following is the work of the rear deck. In order to illumination of the rear deck, installing the LED. Before that, in order to diffuse the LED light, I pasted aluminum tape on the inside of the deck. I made floor with plastic sheets, …
It will return from the base to Arcadia. The next step is illumination of the windows at rear deck. Window parts of the kit has been molded in plastic of clear yellow. So, after you have hollowed out part of the window of the rear deck, it…
I am going to finish the display base and check wire connection and power supply. I disassembled the temporarily assembled base and opened the hole for mounting the switch and jack. (the base that was trial fitting in the past) The left si…
Today, I will set up the Arduino and AtTiny into the Arcadia. Since AtTiny is sensitive to heat, it is not soldered directly, use a dedicated socket. (Socket) Also, the wiring of this project are not many, I did not use a circuit board, I …
Around this time, I was just doing electrical work. In the previous article, I wrote that to control the LED using with the Arduino and another new device. This is it. This small tip is named AtTiny85, and this is also a programmable micro…
it is the time to shink about electrical work. First, I covered LED with aluminum pipe and put glue gun to the both ends. this is going to be LED unit for fiber optic. Some is still single, but I put some LED together like below. With red …
Today's work is almost same as the last time. It illuminate the tip of the rear mast. This part also in the same manner as the main wing, and assembled by bonding a part to the tip of the wing. Although the work is the same as the main win…
Today, turn on the wing-tip light. I will make a small light spot at the tip of the wing. Basically, this is the same way as the work that went before at small wings attached to the top of the bow. I thought it was easier to make it lit fo…
Today I will write about the a little work about the Pulsar Cannon. In the kit, three cannon are formed in one piece.Insert the Cannon from the back side of the body, and assembly. But, it is not seen in the characteristics of Reiji Matsum…
I started to make a display based. Since the Arcadia of the kit is small, it's difficult to install the power supply in.Therefore, the installed power to the display base, and then be routed to Arcadia. The kit comes with display base, but…
Today we will write about the Luminescence of window of the hull. Four square windows that lined beside the the hull. Actually, I am not clear if this is the window or not. In instructions, this place only have been instructed to paint yel…
When I saw this kit, I really would like to illuminate the lantern on top of the rear deck. But, this kit is smaller than I thought, It became difficult work. So small... Because it is impossible to put the LED in it, I made a small light …
Today, it is about the back wall of the rear deck. In this kit, because the back wall is made in one piece, it is not able to illuminate a window in this state. So, I was hollowing out the part of the window. Because I wanted to use a skul…
The following is the illuminations of the engine. Fortunately, there are enough space in the engine unit.So, I would be easily the illumination of work. The first thing to go about is the engine nozzle part.I have split the one-piece parts…