Today's work is almost same as the last time. It illuminate the tip of the rear mast. This part also in the same manner as the main wing, and assembled by bonding a part to the tip of the wing. Although the work is the same as the main win…

Today, turn on the wing-tip light. I will make a small light spot at the tip of the wing. Basically, this is the same way as the work that went before at small wings attached to the top of the bow. I thought it was easier to make it lit fo…

Today I will write about the a little work about the Pulsar Cannon. In the kit, three cannon are formed in one piece.Insert the Cannon from the back side of the body, and assembly. But, it is not seen in the characteristics of Reiji Matsum…

I started to make a display based. Since the Arcadia of the kit is small, it's difficult to install the power supply in.Therefore, the installed power to the display base, and then be routed to Arcadia. The kit comes with display base, but…

Today we will write about the Luminescence of window of the hull. Four square windows that lined beside the the hull. Actually, I am not clear if this is the window or not. In instructions, this place only have been instructed to paint yel…

When I saw this kit, I really would like to illuminate the lantern on top of the rear deck. But, this kit is smaller than I thought, It became difficult work. So small... Because it is impossible to put the LED in it, I made a small light …

Today, it is about the back wall of the rear deck. In this kit, because the back wall is made in one piece, it is not able to illuminate a window in this state. So, I was hollowing out the part of the window. Because I wanted to use a skul…

The following is the illuminations of the engine. Fortunately, there are enough space in the engine unit.So, I would be easily the illumination of work. The first thing to go about is the engine nozzle part.I have split the one-piece parts…

I tried to illuminate another part at the bow. There is very small tree lines need to paint the color of yellow at the bow. I am not sure but in the movie, I think the liens was blighter than the other surface, and I am thinking the liens …

Since the temporary assembly has been completed, I started the work. I use the optical fiber, in order to illumination this kit. Although we will be able to buy the optical fiber in the craft shops and online store, I used the objects for …

The new project is bigan. As always, I started from temporary assembly. The first impression of the kit when I opend the box was,,, There are too many gaps. Because I'm familiar with Gundam a lot, I thought that there is little parts in th…

I am going to start next project. Next my project is,,,not creature figure, not Gunpra. The new project is a Space Pirate Battle Ship name is Arcadia. The kit is from Hasagawa. I would like to get this kit for while, but it was soo hard to…

Today, I will post the complete photo of Chestburster.When I finised basic paint work, I took some pictures before I do weathering. Because, this is my first creature figure work and I was not sure I could finish some effects well. So, I w…

After I had finished the base, I started weathering. Chestburster was clear coated and waited for be weathered. !!!!!Warning!!!!! I said I did weathering, but is is not ordinary weathering for Mecha. I add some biological effects like sali…

Once, I stop the article of chestburster, I will write about the base. I went to look for a good material to use for the base at hardware store. And, I found a good material. The cat is my assistant. She is helping me all the time. It is a…

I found that blood vessel was too clear to see even if I repeated a skin color several times. Therefore, by overlapping the blue color using airbrush from the top of the vessel to blur around. I have painted the arms and legs to like the p…

Today I will write an article for the entire painting. After I finished surface treatment, I started base painting. I used a color of Red-Orange for base paint. Painted all over the kit using airbrush Except the head dome. The other parts …

I started painting from the Head part first. Some kits has clear part for head dome, but this soft vinyl kit does not. So, I would like to have a expression that unlike with other part. I tried to use Hammered paint from Rust-Oleum. I just…

I start another my project, and this is the first Figure project in my blog. It is Figure, but it isn't bishojo figure, it is a creature from my favorite movie series "Alien". I have got the kit from my co-worker more than 10 years ago, bu…

Bandai Master Grade RB-79 Mobile Pod Ball Ver.Ka is completed. I would like to share some pictures, and I hope you like it. This time I did not do major modifier, just cut and remove some Exterior panels. I've painted with the image of mec…

After I finish all work for Ball, I started finish the display base. It is not an elaborate work, just using Action Base from Bandai with a little paint work. 1st, I put a rod in to the main thruster. This will be a stand arm. The main thr…

I finised 1st stage of the weathering, and going to add some more weathering. I add splattered oil dirt on he entire kit. I put the thinned paint(brown, or ark yellow) in toothbrush, and blowing the paint by rubbing the tooth brush in fron…

After the kit was coated with clear spray, I can start weathering. I did the weathering using oil paint as usual. First, I added water, rust and oil stains with black oil paint. I added same effect as cockpit hatch on side camera housing. …

Today, I am going to write about exterior panel. I was starting weathering from Cockpit Hatch. The parts was painted with flat white using spray paint first, then paint dark (wine?) red using air brush. I did wet sanding using very fine pa…

After all parts was glued, I started painting. The Master Grade kit is divided into many parts, so I do not need mask most of the place. Just paint. I would like to get strong paint coating, so I use Tamiya Spray Paint for color of white a…

After temporarily assembled, I did a little modifications to body shell parts. I would like to make this Ball like Star Wars mecha. I cut some body panel to expose inner frame. The area marked with red .pencil was detached from a body pane…

I am starting new production article. I finised this kit some years ago, but I took a lot of pics and I would like to share it. next item is RB-79 Ball from Bandai Master Grade. as always, I did Temporarily assemble first to check where I …

Bandai Master Grade MS-07B Gouf is completed. I would like to share some pictures. front view rear. I have changed the shape of the head. I have expanded the width of the mouth, also, it has been extended. So now, mouth will overlays on to…

Based paint is finished, and put decals, then following is weathering. First, in order to protect the base paint ans decals from weathering, I sprayed clear coat. Once the clear coat is dried, I will start the weathering. I used oil paint …

My work came to painting process. Before painting, by spraying the surfacer in overall, to check whether the surface is being processed properly. If found any problems, sanding again, and repeat to the painted the surfacer. If there is no …