I started to make a mono-eye. First, I cut the aluminum pipe with a pipe cutter to make the frame of Mono-Eye. Then, I have to sharpen flat LED's round head. I also sharpen periphery according to the inner diameter of the pipe. LED has bee…

I started assembling the left arm. By connecting a pipe which I cut diagonally, I changed the angle of the arm. During the work to change the angle,I thought way of coming out of claw is not good. The form of the kit, it looks like a clow …

Both legs assembled rough, I began to assemble the body and both arms. I will keep the shape of the original essentially the right arm. However, in the same way as leg, I have to be able to level the arm by cutting the arm where the hits. …

Since I made ​​a GM roughly, I started making the Z'Gok. Joint does not move much the same as GM also Z'Gok. However, this model is a fixed-pose, so pose of Gm by bending the joint by cutting and/or adding. I began to sharpen from the righ…

It is soooo slow, but I am wtill working. I am thinking that I will use both arms as is,,,I hope... It is so simple. At first, I was going to replace the Detail Up Parts just part of the hands, but when I checked detali up parts at hobby s…

The bud came out four days afterward. Furthermore, it became like grass completely three days afterward. If a switch is turned on, a water wheel will also turn. All done!! Thank you for watching.

1. A mat is aligned with the ground and cut off with scissors. After covering with a mat, water is put into a base. Seeds (attachment) are planted on a mat. A bud comes out after around 5days.The spray of the water is sometimes carried out…

7 FinishAfter installing a watermill, a guttering, No. 25, and No. 21 are pasted up. Accessories and Kakinoki(a persimmon tree) are installed in a favorite position. Complete view A light is wired. Black wire is from the light. Light's up.…

Assemble Water Mill (reverse side)1 Paste up 13 and#14 (12 sets is made). And it is made to move freely, although it lets it pass in the hole of #11 and #12 without pasting up. All other parts glued on #1 2 Cut "Shoji-paper" (very, very th…

水中ポンプの組立(assrmble a water pump)1 Try to be careful of an illustration and a photograph.The part of No. 6 is not pasted up on No. 5. Since the portion becomes a switch, it should move freely. Small light bulb pass #24(glued on #11) …

This kit is very old style and the detail and overall style is not so good. In the original plan, I fix roughly the shape of the entire image without touching too much, but I think it even more difficult. Remodeling of the body has continu…

屋根の組み立 assemble Roof1 Spread palm on the roof (parts number 22) using glue(any kind, you can get this glue at local home center). the palm should be 1-2mm thickness. After spread the palm, put rubber band and fix on the roof until th…

I am going to introduce another project. This is a Water mill kit from Japanese miniature garden seriese. Before you start assemble the kit, better to check all parts with instruction. And read instruction (yes, it is Japanese, so you may …

I bent the hip joint parts using small burner. If legs is inclined forward, thigh hits back armor. So I off-set joint part to forward。 The lower part of the body looks like below?

When I lived in Japan, I own Suzuki GSX1100S Katana. I loved the bike sooooo much, but I have to leave it in Japan because I can not get license plate for the bike in California. I tried to find any way to bring my Katana and ride it in CA…

I decided to separate more at skirt parts. Caution!!! Do not hold parts and using saw like the pic. I cut my finger 5sec. after took the pic. Now, it is separated so many parts.... can I put it back together???

The FG kit has very limited range of moving limbs. So, my first mork is separate body parts. The body section is made by only 2 parts, just a front side and a back side. I cut on the waist line and meke it upper half and lower. Also, cut w…

I start new project useing these kits. When I went back Japan the last time, I found these kits. I thought it was sooooo nostalgic, because when I was kid I collected and built those ans the other Gunpla a lot. The price was 210 Japanese y…

please contact us from this form. Loading…

I had started my brog from last month in Japanese, and I am going to star the brog in English, too. I will share my model buiding mainly and some other fablications also. I hope someone will enjoy my entry.

This is a personal blog. Any views or opinions represented in this blog are personal and belong solely to the blog owner and do not represent those of people, institutions or organizations that the owner may or may not be associated with i…